Series 1048 Short Tee

Series 1047 90 Degree Elbow

Series 1047 – The 90 Degree Elbow is designed to provide a joint between two pipes at right angles to each other. It is often used as railing ends or corners on a level installation.   PART NUMBER A F G 1047.32 2.48 1.38 1.30 1047.40 2.60 1.38 1.42  

View more

Series 1049 Long Tee

Series 1049 - The Long Tee is designed to provide a butt joint between two pipes at right angles to each other. It allows the through pipe to be joined inside the fitting, and is an alternative to a Series 1048. This fitting... 

View more

Series 1050 Railing Base Flange

Series 1050 – The Railing Base Flange is designed to provide structural fixing to guardrail and balustrades. The holes are sufficient diameter to provide good fixing with either mechanical or chemical anchors. PART... 

View more

Series 1051 3-Way Blind Corner

Series 1051 – The 3 Way Blind Corner is designed as a corner fitting for the upper rail of handrails, guardrail or frames. PART NUMBER A F G 1051.32 2.48 1.38 1.32 1051.40 2.60 1.38 1.42  

View more

Series 1052 3-Way Open Corner

Series 1052 – The 3-Way Open Corner, with its through hole, is designed as a corner fitting for a middle rail of handrails, guardrails or frames. PART NUMBER A F L 1052.32 2.48 1.38 2.24 1052.40 2.60 1.38 2.48  

View more

Series 1053 Short Cross

Series 1053 – The Short Cross is designed as a middle rail joint for handrail and other structures. The center pipe cannot be joined inside the fitting. PART NUMBER E G L M 1053.32 0.67 1.30 4.96 2.24 1053.40 0.67 1.42 5.20 2.48  

View more

Series 1054 Straight Sleeve

Series 1054 – The Straight Sleeve is designed to provide an inline joint between two pieces of pipe of the same size. Where a constant diameter is required along the outside of the pipe, use Series 1055, an expanding... 

View more

Series 1058 Base Flange

Series 1058 – The Base Flange is designed to provide a positional wall or base fixing. It is not recommended to use this fitting as a railing base. PART NUMBER A E L 1058.32 4.02 0.67 2.13 1058.40 4.49 0.67 2.36  

View more

Series 1060 Wall Flange

Series 1060 – The Wall Flange is designed to provide a base fitting for railings requiring a side mounted fixing. The upright cannot pass through the fitting. PART NUMBER A L N P 1060.32 4.02 3.90 3.07 4.57 1060.40 4.25 4.13 3.31 4.80  

View more

Series 1061 Rail Bracket

Series 1061 – The Rail Bracket is designed to secure handrail pipe to a wall. It can also be used on the top of a wall to secure a lower rail. Pipes cannot be joined inside this fitting. PART NUMBER A E F L 1061.32 1.89 2.44 3.35 4.53 1061.40 1.97 2.68 3.35 4.53  

View more

Series 1062 Side Outlet Tee

Series 1062 – The Side Outlet Tee is designed to provide a three way joint for handrails and other structures. The center pipe cannot be joined inside the fitting. PART NUMBER A E L M 1062.32 2.48 0.67 2.24 4.96 1062.40 2.60 0.67 2.48 5.20  

View more

Series 1063 4-Way with Center Pipe

Series 1063– The 4 Way With Center Tube is designed to provide a four way connection to an upright. The center pipe cannot be joined inside the fitting, but it can end inside the fitting and be capped using a Series... 

View more

Series 1064 Short Tee Swivel

Series 1064 – The Short Tee Swivel is designed to provide corner joints with angles varying from 90 to 180 degrees. Sold in pairs. PART NUMBER A E G L M 1064.32 2.91 0.67 1.30 1.77 1.12 1064.40 3.23 0.67 1.42 1.97 1.24  

View more

Series 1065 Adjustable 2 Socket Cross

Series 1065 – The 30 to 45 Degree Adjustable 2 Socket Cross is designed to fasten the middle rail to an intermediate upright, which must remain vertical. It can accommodate slope angles from 30 to 45 degrees. PART... 

View more

Series 1067 Variable Angle Tee

Series 1067 – The Variable Angle Tee is designed to fasten top rails to end uprights on slopes from 30 to 60 degrees, or any tee joint requiring this range of angle. PART NUMBER A E F K L 1067.32 3.74 0.67 0.98 1.97 2.48 1067.40 4.13 0.67 0.98 2.20 2.68  

View more

Series 1073 Single Male Swivel

Series 1073 – The Male Swivel is used in combination with a Series 1074 to make an Series 1080 Single Swivel Kit. PART NUMBER A G L 1073.32 1.89 1.30 1.89 1073.40 2.01 1.42 1.89  

View more

Series 1074 Single Female Swivel

Series 1074 – The Female Swivel is designed to be used in combination with a Series 1057.25 or Series 1073 or Series 1076 or Series 1077 to make “Swivel Kits” used primarily for bracing, but can also be used to overcome problems... 

View more

Series 1075 Alternate Male Swivel

Series 1075 – The Male Swivel designed to be used in combination with an a Series 1074 and a Series 1079 to create a combination fitting that will provide an angled strut so support an existing structure without dismantling.... 

View more

Series 1076 Double Male Swivel

Series 1076 – The Double Male Swivel is designed to be used in combination with two Series 1075’s to form a Series 1082 Double Swivel Kit. It is used to provide an inline angled joint to an upright, suitable for the middle... 

View more

Series 1077 90 Degree Corner Male Swivel

Series 1077 – The 90 Degree Corner Male Swivel is designed to be used in combination with two Series 1073’s to form a Series 1091 – 90 Degree Corner Swivel Kit. It is used to provide an inline 90 degree joint to an upright,... 

View more

Series 1078 Cross Over

Series 1078 – The Cross Over is designed to fasten two pipes at 90 degrees to each other and off set. Used for shelf or pallet racking to join horizontal carrying rails to the uprights. Pipes cannot be joined inside the fitting. PART... 

View more

Series 1079 Clamp on Tee

Series 1079 – The Clamp On Tee is designed to allow new pipe to be joined to existing structure. It can be used in combination with a Series 1074 and Series 1075. PART NUMBER F G L 1079.32 2.48 1.30 1.67 1079.40 2.68 1.42 1.91  

View more

Series 1080 Single Swivel Kit

Series 1080 – Single Swivel Kit The Single Swivel Kit is composed of all Series 1080 Single Female Swivel connected to Series 1075 Single Male Swivel with a stainless steel bolt, nut and washers. It is designed to serve as... 

View more

Series 1081 Base Swivel Kit

Series 1081 – Base Swivel Kit The Base Swivel Kit is composed of a Series 1074 Single Female Swivel connected to an 1057.25 Swivel Base with a stainless steel bolt, nut and washers. It is designed to serve as a variable angle... 

View more

Series 1082 Double Swivel Kit

The Series 1082 Double Swivel Kit is composed of two Series 1074 Single Female Swivel fittings connected to an Series 1076 Double Male Swivel fitting with stainless steel bolts, nuts and washers. It is designed to provide... 

View more

Series 1083 90 Degree Corner Swivel Kit

Series 1083 – Double Swivel Kit The Double Swivel Kit is composed of two Series 1074 Single Female Swivel fittings connected to an Series 1076 Double Male Swivel fitting with stainless steel bolts, nuts and washers.... 

View more

Series 1084 Spare Screws

The Series 1084 Spare Screws are made of Stainless Steel (BS970GR420), and come in two sizes: 1/4″ BSP for the Size 25 and 3/8″ BSP for the Size 32 and Size 40.  

View more

Series 1085 Plastic End Cap

The Series 1085 Plastic End Caps are designed to seal open ended pipes utilizing a friction fit. For a more permanent fix, an appropriate adhesive should be used. Can be used with Schedule 40 and Schedule 80 pipe.  

View more

Series 1089 Inline Swivel Kit

Series 1089 Swivel kit is an inline fitting to allow adjustment to you section of rail. This fitting is designed to be maneuverable within any inline railing system. PART NUMBER 1089.32 1089.40  

View more